Woodstock SHOP FOX M1001 Especificações

INSTRUCTION MANUALMODEL M1001 6" X 26" VERTICAL MILLPhone: (360) 734-3482  •  On-Line Technical Support: [email protected] ©

-8-M1001 6" x 26" Vertical MillSAFETYAPPROVED OPERATION. Untrained operators can be seriously hurt by machinery. Only allow trained or prope

-9-M1001 6" x 26" Vertical MillSAFETYAdditional Safety Instructions for Vertical MillsUSE this and other machinery with caution and respect

-10-M1001 6" x 26" Vertical MillELECTRICALAvailabilityBefore installing the machine, consider the availability and proximity of the required

-11-M1001 6" x 26" Vertical MillELECTRICALNote: The circuit requirements listed in this manual apply to a dedicated circuit—where only one m

-12-M1001 6" x 26" Vertical MillELECTRICALGrounding & Plug RequirementsThis machine MUST be grounded. In the event of certain malfunctio

-13-M1001 6" x 26" Vertical MillSET UPThe SHOP FOX® Model M1001 has been carefully pack-aged for safe transporting. If you notice the machi

-14-M1001 6" x 26" Vertical MillSET UP60"41"Figure 5. M1001 minimum working clearances.• Floor Load: Your vertical mill has a lar

-15-M1001 6" x 26" Vertical MillSET UPAlthough not required, it is recommend that you mount your new mill to the floor. Because this is an o

-16-M1001 6" x 26" Vertical MillSET UPFigure 10. Headstock lock nuts.Figure 11. Handwheel locations.Figure 12. Drawbar location.The longitud

-17-M1001 6" x 26" Vertical MillSET UPNOTICEFollow spindle break in procedures on Page 24 after the test run and before performi

This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, r

-18-M1001 6" x 26" Vertical MillOPERATIONSOPERATIONSGeneralDO NOT investigate problems or adjust the mill while it is running. Wait until th

-19-M1001 6" x 26" Vertical MillOPERATIONSTo rotate the spindle head horizontally, do these steps:1. UNPLUG THE MILL!2. Make sure t

-20-M1001 6" x 26" Vertical MillOPERATIONSThe table handwheels and the knee handle have graduated dials. Each mark represents 0.001" of

-21-M1001 6" x 26" Vertical MillOPERATIONSQuill Feed ControlThe quill feed is controlled by the quill feed handle shown in Figure 20. The ha

-22-M1001 6" x 26" Vertical MillOPERATIONSBefore changing speeds, you must first determine the best RPM to use with the material and diamete

-23-M1001 6" x 26" Vertical MillOPERATIONSSetting the RPM on the Model M1001 involves placing the V-belts on the pulleys as shown in the spi

-24-M1001 6" x 26" Vertical MillOPERATIONSSpindle Break-in ProcedureComplete this process once you have familiarized yourself with all instr

-25-M1001 6" x 26" Vertical MillOPERATIONSTo load a tool in the spindle, do these steps:1. UNPLUG THE MILL!2. Turn the mill OFF, allow it

-26-M1001 6" x 26" Vertical MillMAINTENANCEMAINTENANCEMAKE SURE that your machine is unplugged during all maintenance pro-cedures! If

-27-M1001 6" x 26" Vertical MillMAINTENANCELubricationPower FeedThe power feed uses SAE 40 oil and should not need to be changed unless the

SET UPELECTRICAL MAINTENANCESERVICE PARTSOPERATIONSSAFETYINTRODUCTIONUSE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!Table of ContentsI

-28-M1001 6" x 26" Vertical MillMAINTENANCEMaintenance NotesMaintenance ScheduleDaily:• Pump handle of the one shot lubrication system 2-4

-29-M1001 6" x 26" Vertical MillSERVICESERVICEThis section covers the most common service adjustments or procedures that may need to be made

-30-M1001 6" x 26" Vertical MillSERVICEFigure 33. Cross nut.Figure 32. Longitudinal nut.Adjusting BacklashBacklash is the amount of play fou

-31-M1001 6" x 26" Vertical MillSERVICEThese pages are current at the time of printing. However, in the spirit of improvement, we may make c

-32-M1001 6" x 26" Vertical MillSERVICEFigure 34. M1001 Electrical panel.Terminal BarDZ47 ContactorDZ47LE C32 ContactorTransformerWiring Box

-33-M1001 6" x 26" Vertical MillSERVICEContactor110V(230V)Reverse SwitchStarter2AU1V2Z2Z1110V(230V)24V,40WMotor110V wiring for motor230V wir

-34-M1001 6" x 26" Vertical MillSERVICETroubleshootingThis section covers the most common problems. WARNING! DO NOT make any adjust-ments un

-35-M1001 6" x 26" Vertical MillPARTSHeadstock Assembly2567157711685455705841393815215115315115240391371016969376614121125170687060616772593

-36-M1001 6" x 26" Vertical MillPARTS1448685848312612513079751287677127143119921398136127918012212012710410310212878130848586144127998788133

-37-M1001 6" x 26" Vertical MillPARTSREF PART # DESCRIPTION REF PART # DESCRIPTION1 XM1001001 VERTICAL MILLING HEAD 50 XM1001050 COIL SPRING

-2-M1001 6" x 26" Vertical MillINTRODUCTIONWoodstock Technical SupportWe stand behind our machines! In the event that questions arise about

-38-M1001 6" x 26" Vertical MillPARTSREF PART # DESCRIPTION REF PART # DESCRIPTION95 XM1001095 CROSS LEAD SCREW 136 XPSB31M CAP SCREW M8-1.2

-39-M1001 6" x 26" Vertical MillPARTSMachine LabelsSafety labels warn about machine hazards and how to prevent machine damage or injury.

WAR RANTYWoodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years

M1001 6" x 26" Vertical MillCUT ALONG DOTTED LINEName ___________________________________________________________________________________Str

TAPE ALONG EDGES--PLEASE DO NOT STAPLEFOLD ALONG DOTTED LINEFOLD ALONG DOTTED LINEWOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-230

-3-M1001 6" x 26" Vertical MillINTRODUCTIONModel M1001 Machine Specifications, Page 1 of 3MODEL M1001SHOP FOX® VERTICAL MILL 6" X 26&qu

-4-M1001 6" x 26" Vertical MillINTRODUCTIONModel M1001 Machine Specifications, Page 2 of 3Table InfoTable Length...

-5-M1001 6" x 26" Vertical MillINTRODUCTIONModel M1001 Machine Specifications, Page 3 of 3ElectricalPower Requirement...

-6-M1001 6" x 26" Vertical MillINTRODUCTIONControls and FeaturesA. Longitudinal HandwheelB. WorklightC. 3" Shell Mill D. Quill Micro

-7-M1001 6" x 26" Vertical MillSAFETYIndicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate inju